The Radavist

This year’s Philly Bike Expo coverage over here is going to be a bit different. John was supposed to attend but two freak storms hammered Santa Fe Thursday and Friday, cancelling his flights and his re-booked flights. Luckily, our friend Brad Quartuccio was on hand to document a few bikes for us. The first builder we’re featuring is Kris from 44 Bikes, who displayed his current version of the Snakedriver full-suspension 29er…

When I lived in New York City, we rode our bikes to Philadelphia every year for the Philly Bike Expo. At the time, the event was hosted inside an old armory in the city, and featured a handful of framebuilders, makers, and companies with roots mostly in commuter cycling. Back then, the Philly Bike Expo felt like a family. I moved out of the Northeast shortly after and was really looking forward to reconnecting with old friends.

The last time I made it to an Expo was in 2012, and a lot has changed. While the same soul is still very much present, the venue, size, and impact of the Philly Bike Expo have grown. After a two-year pandemic hiatus and a relatively subdued 2021 year, it was back and bigger than ever for 2022. Cari and I flew to Philadelphia to get out of Santa Fe for a few days, soak in some big(ger) city food, and take in the Expo, so let’s get to it.

Continuing on with our 2021 ENVE Builder Round Up coverage – we posted the first Gallery on Friday – today we’re featuring the show-stopping work of Prova Cycles, Naked Bicycles, 44 Bikes, Spooky, Retrotec, and Argonaut Cycles. Each of these builders brought something special to the showcase and a few raised the bar considerably in various ways. There’s a lot to go over here so let’s get to it!

My first taste of full suspension came when I was working as a wrench at a shop in Quakertown PA just after graduating from college and not really having a plan. On mornings off, I’d take out a demo and ride the local trails up on South Mountain in Emmaus. Those bikes were terrible. But at the time, I was young and loving any bicycle I could get my hands on. That was 1998. A degree project when I went back to school confirmed I didn’t have a clue about geometry, handling, let alone suspension kinematics. Fast forward to 2012 when I hung my shingle out starting 44 Bikes, I became solely focused on honing geometry and understanding fit. But deep down, I wanted to build a full suspension bike but I knew I wasn’t ready. Which brings us to the here and now. Things began to click after building hundreds of bikes and dozens of prototypes where I finally felt like I had a grip on geometry and handling. I wanted a new challenge. So in the Spring of 2019, I started acquainting myself with a platform I had largely ignored.

The Marauder from 44 Bikes is one hell of a versatile bike, available in steel and titanium, it blurs the line between shreddy MTB and bikepacking bike, sub out to a suspension fork and rip your local trails, or ride it rigid and pack on a few extra pounds of fun.  Kris actually made all of the bags in-house, including the panniers, frame bag, and the stem sacks.  It’s pretty rad to see a frame builder tackle some sewing in addition to wielding a torch. Running a Lupine Lights Pika in lieu of a dynamo allows Kris to run the same wheelset in shred mode as a full touring mode. He even made the rack and fork in house.

Kris built the bike with a mix of Shimano XTR 9100 and XT 8100 brakes, Industry Nine Wheels, a Fox Transfer dropper post and a Wolf Tooth Remote. This bikepacking bike swears to shred, that for sure!

2017 Philly Bike Expo: 44 Bikes Titanium Marauder SSMTB
Photos by Jarrod Bunk, words by John Watson

Last year, we saw Kris from 44 Bikes‘ first super-boosted Ti Marauder SSMTB from our Philly Bike Expo coverage. This year, Kris brought a new Marauder to display, with some geometry tweaks, different components, and a slightly longer and slacker stance. The big difference this year is he used a super boost hub with a standard 73mm T47 bottom bracket mated with a custom 170mm i9 fatbike hub, built with a standard axle, wheras last year, he used a wider q-factor with a DH BB. Kris machined the bits needed to make this happen and the whole package results in a stiffer rear wheel.

Traditionally, single speed mountain bikes are heralded for their simplicity, yet this one has a lot going on!

____

Follow Jarrod on Instagram, and 44 Bikes on Instagram

Two Years In… Packing for a Long-Term Bike Tour
Photos and words by Ryan Wilson

Packing for a trip that spans multiple years can be a bit daunting.  Especially when you’ll be passing through just about every zone of climate you can possibly imagine, from the humidity and heat of the Peruvian jungle to the bitter cold of winter in the mountains of Patagonia…  Dragging the bike up rugged 16,000ft hiking trails, across remote dirt roads, or even the occasional stretch of asphalt. Walking the fine line between having an excessive amount of stuff or too little is a tricky balance.

My setup has been gradually refined since I first started this trip two years ago, and while it’s far from a “minimal” or “ultralight” setup you might take on a trip that spans a few weeks or less, I think I’ve struck a reasonable balance between having everything I need to live and work on the bike in the long-term, while still being a rig that is fun to ride no matter how rough the terrain gets.

As time has gone on, I’ve found that the overall weight doesn’t really matter as much as how everything is packed.  It’s when bags are bouncing around loosely or swaying back and forth where the size and weight really becomes a burden.  When everything is tight and dialed, it’s just another bike.  “How much does it weigh?” is a question I’ve been asked hundreds of times along the way and to be honest, I don’t have a clue.  Ignorance is bliss, I guess.

There are some things on here that would be overkill for many people (large camera, computer, etc), and some things that would be a bit too minimal for others (clothes, sleeping bag, etc), but this is what works for me at the moment…

Kris Henry from 44 Bikes knows how to craft a beautiful, functional tig-welded machine that will live by the brand’s mantra of “Swear to Shred.” This Huntsman road bike features clearances for WTB Nano tires, Shimano flat mount brakes, the powerhouse group that is Ultegra, and a geometry tuned for road riding of all substrates. With a paint job by Jordan Low of Hot Tubes Paint, it’s got plenty of pop!

Continuing our documentation of these high desert Pack Mules, is my 44 Bikes rigid mtb tourer, decked out in desert bikepacking mode, with a few key adjustments to its normal build we’ve seen before.

This bike proved itself on our 100 mile Prospector’s Tour of Death Valley but initially, I was worried. Worried for a few reasons, but mostly because of the tire size. While riding in the desert is not new to me, doing it fully loaded, for four days, in Death Valley is. Everything in my mind told me to track down a fat bike for the route. After driving it last month, I was aware of every change in ground substrate; the Eureka Valley presented sand and loose tuff. Steel Pass was gravely, with corners suddenly sinking into inches of loose rocks and the climbs out of Saline Valley are washboarded, rocky and can take a toll on your hands.